Programmer BeeProg2c

Universal Programmer memory, microcontrollers and PLDs. This supports systems 78324

Beeprog2c programmer Elnec company is an excellent choice for factories and businesses servicing the electronic devices

General info – Programmer BeeProg2c

->BeeProg2c hardware is identical to the programmer BeeProg2. The only differences appear in the software. 

BeeProg2c has several limitations in relation to the programmer BeeProg2:

  •  
  • does not support already withdrawn from production in 2708 EPROMs 
  • LPT interface is blocked by software 
  • no service has already withdrawn from the production series microcontrollers MCS48 
  • no longer supports bipolar circuits (PROMs and PLDs) 
  • no service has already withdrawn from the production of EPROM programming voltage 21V and higher 
  • are not supported already withdrawn from the production of microcontrollers 8751/8752 programming voltage 21V or higher
-> Programmer BeeProg2c can be upgraded at any time to BeeProg2 model by using a special kit .
 
-> Programmer Beeprog2 may also be a tester logic TTL / CMOS memory. It allows users to create sequences of test patterns
 
– > Built-in patronage systems, which allows to eliminate damage to the programmer or would be . All inputs programmer BeeProg2 (including the ZIF socket , power supply or USB ) are protected against ESD up to 15kV .
 
-> There are adapters to systems in PLCC , JLCC , SOIC , SDIP , SOP, PSOP , SSOP , TSOP , TSOPII , TSSOP , QFP , PQFP , TQFP , VQFP , QFN ( MLF ) , SON , BGA , EBGA , FBGA , VFBGA , uBGA , FTBGA , LAP , CSP , SCSP , LQFP, MQFP , HVQFN , QLP , QIP .

Hardware of Beeprog2c

-> The programmer is equipped with a system FBGA – With 48 pindriverami programmer allows you to call the states of H / L / pull up / pull down. Each of the pins can read the data. Pindrivery can actuate voltage from 1.8V level allowing us to serve a wide range of low-voltage systems 
 
-> BeeProg2 checks the correct placing in a zif socket (or has been placed in the correct place stand) and checks the quality of the connection between the legs and the seat base systems. 
 
-> Overcurrent protection and control byte signature to help prevent damage due to an error of use 
 
-> BeeProg2 selftest has features that allows you to zdiagnazowanie its technical condition. 
 
-> All inputs programmer BeeProg2 (including the ZIF socket, power supply or USB) are protected against ESD up to 15kV.

Software for programmer Beeprog2c

-> The timer is controlled through an easy -to-use software. The selection of the system can be made by the class , manufacturer, or type part of the catalog number of the system .
 
-> The program supports all popular file formats . Files can recognize and convert automatically while loading the file.
 
-> Software allows you to perform standard commands related to handling systems – (read , blank check , program , verify , erase) , and has additional features : test (test whether the correct placement of the test signature byte ) , autoincrement , production mode ( automatic start work after system is inserted into the cradle )
 
-> Autoincrement function enables to assign the programmed system to an individual serial number. It allows you to read from the file serial number or other identifying signature system
 
-> Software provides basic information about the system ( displays the available drawings of housings in which the system is dimensioned , part numbers are decoded systems (how the system in the name of the manufacturer writes its basic parameters )
 
-> Provides information on the implementation of ISP ( ISP pins for layout, wiring diagram and additional electronic components required for in-system programming )
 
-> PG4UW program can also be controlled by an external application.
 
-> Software allows you to connect several programmers BeeProg2 to one computer . We can program the system of multiple programming . It is a program of „” concurrent „” – each programmer works independently so you can program different layout.
 
-> The software is only used algorithms certified or approved by the manufacturers of systems . Individual algorithms are available on request for an additional fee .
 
-> Free update software ( algorithms ) are available on a regular basis once every 4 weeks
 
-> BeeProg2 programmer is universal and therefore support these new systems requires only a software update.

Sample times of programming via BeeProg2c

Chip Dimensions Operations Time
Am29DL640G (parallel NOR Flash) 400080hx16 (64 Mega) programowanie i weryfikacja 24 s
K8P6415UQB (parallel NOR Flash) 400100hx16 bit (64 Mega) programowanie i weryfikacja 13 s
K9F1G08U0M (parallel NAND Flash) 8400000Hx8 (1 Giga) programowanie i weryfikacja 122.7 s
QB25F640S33 (serial Flash) 800200hx8 (64 Mega) programowanie i weryfikacja 30.7 s
AT89C51RD2 (microcontroller) 10000Hx8 programowanie i weryfikacja 14.4 s
PIC32MX360F512L (microcontroller) 80000hx8 programowanie i weryfikacja 16.2 s

Test Parameters: PC Pentium 4, 2.4 GHz, 512 MB ​​RAM, USB 2.0 HS, Windows XP. Please note that Elnec programming speed tests using randomly created data pattern. Programming speed slightly depends on the speed of the PC. If the programmer is connected to the PC after the LPT port – programming may take a little longer.

 

Technical specifications programmer BeeProg2c

Unit DAC’s

    •  
    • USB 2.0 high-speed – up to 480Mbit / s 
    • electronics intelligence: powerful microprocessor and a state machine for FPGA 
    • three converters D / A converters that produce regulated, independent power supply systems (VCCP, VPP1, VPP2) with a controlled rise time and fall slopes 
    • VCCP range from 0 to 8V/1A 
    • VPP1, VPP2 range from 0 to 26V/1A 
    • built-in starter test and auto-calibration function
    •  

Socket zif and pin drivers

  •  
  • Universal 48 pin DIL ZIF (Zero Insertion Force) for systems with a width of 300/600 mils, from 8 to 48 pins 
  • 48 universalych pin drivers 
  • For each of the pin drivers can be independently connected voltage VCCP, VPP1 and VPP2 
  • good grounding each of the pins 
  • Drive capability of each of the 48 pins Logic: H, L, CLK, pull-up, pull-down 
  • Full support for low voltage 1.8V already 
  • ESD protection on each pin base (IEC1000-4-2: 15kV air, 8kV contact) 
  • test: each pin is tested before every programming

 ISP connector 

  •  
  • 20-pin male 
  • 6 pin drivers to provide TTL logic states: H, L, CLK, pull-up, pull-down. H level can be set between 1.8V .. 5V 
  • 1 x VCCP (range 2V..7V/100mA) 
  • 1 x VPP (range 2V..25V/50mA) 
  • ESD protection on each pin base (IEC1000-4-2: 15kV air, 8kV contact) 
  • 2 outputs: working status LED OK and LED Error (active level: min 1.8V) 
  • 1 input, equivalent to the YES button! (active level: max 0.8V)

Programmer BeeProg2 includes:

  •  
  • Programmer BeeProg2c 
  • power Cable 
  • Cable for connecting to a PC USB 
  • cable ISP 
  • Adapter for diagnostic test ISP interface 
  • The cover protects against dust stand 
  • documentation 
  • CD with software

Systems programmed by the programmer BeeProg2

In ZIF socket

  • EPROM: NMOS/CMOS, 2708*, 27xxx and 27Cxxx series, with 8/16 bit data width, full support for LV series
  • EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, with 8/16 bit data width
  • Flash EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx series, Samsung’s K8Fxxxx, K8Cxxxx, K8Sxxxx, K8Pxxxx series, from 256Kbit to 1Gbit, with 8/16 bit data width, full support for LV series
  • NAND FLASH: Samsung K9xxx, Hynix HY27xxx, Toshiba TC58xxx, Micron MT29Fxxx, Spansion S30Mxxx, Numonyx (ex STM) NANDxxx
  • LBA-NAND: Toshiba THGVNxxx
  • mDOC H3: SanDisk (ex M-Systems) SDED5xxx, SDED7xxx, MD2533xxx, MD2534xxx, Hynix HY23xxx
  • Multi-chip devices: NAND+RAM, NOR+RAM, NOR+NOR+RAM, NAND+NOR+RAM
  • FRAM: Ramtron
  • MRAM: Everspin MRxxxxx8x
  • NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK STKxxx, XICOR 2xxx, ZMD U63x series
  • PROM: AMD, Harris, National, Philips/Signetics, Tesla, TI
  • Serial E(E)PROM: Serial E(E)PROM: 11LCxxx, 24Cxxx, 24Fxxx, 25Cxxx, 59Cxxx, 85xxx, 93Cxxx, NVM3060, MDAxxx series, full support for LV series, AT88SCxxx
  • Serial Flash: standard SPI (25Pxxx, 25Fxxx, 25Lxxx, 25Bxxx, 25Txxx,25Sxxx, 25Vxxx, 25Uxxx, 25Wxxx, 45PExx), high performance Dual I/O SPI (25Dxxx, 25PXxxx), high performance Quad SPI (25Qxxx, 26Vxxx), DataFlash (AT45Dxxx, AT26Dxxx)
  • C
  • onfiguration (EE)PROM: XCFxxx, XC17xxxx, XC18Vxxx, EPCxxx, EPCSxxx, AT17xxx, AT18Fxxx, 37LVxx
  • 1-Wire E(E)PROM: DS1xxx, DS2xxx
  • PLD Altera: MAX 3000A, MAX 7000A, MAX 7000B, MAX 7000S, MAX7000AE, MAX II/G/Z
  • PLD Lattice: ispGAL22V10x, ispLSI1xxx, ispLSI1xxxEA, ispLSI2xxx, ispLSI2xxxA, ispLSI2xxxE, ispLSI2xxxV, ispLSI2xxxVE, ispLSI2xxxVL, LC4xxxB/C/V/ZC/ZE, M4-xx/xx, M4A3-xx/xx, M4A5-xx/xx, M4LV-xx/xx, ispCLOCK, Power Manager/II, ProcessorPM
  • PLD: Xilinx: XC9500, XC9500XL, XC9500XV, CoolRunner XPLA3, CoolRunner-II
  • other PLD: SPLD/CPLD series: AMI, Atmel, AMD-Vantis, Gould, Cypress, ICT, Lattice, NS, Philips, STM, VLSI, TI
  • FPGA: Actel: ProASIC3, IGLOO, Fusion
  • FPGA: Lattice: MachXO, LatticeXP, ispXPGA
  • FPGA: Xilinx: Spartan-3AN
  • Clocks: TI(TMS), Cypress
  • S
  • pecial chips: Atmel Tire Pressure Monitoring ATA6285N, ATA6286N, PWM controllers: Zilker Labs, Analog Devices, Gamma buffers: TI, Maxim …
  • Microcontrollers 48 series: 87×41, 87×42, 87×48, 87×49, 87×50 series
  • Microcontrollers 51 series: 87xx, 87Cxxx, 87LVxx, 89Cxxx, 89Sxxx, 89Fxxx, 89LVxxx, 89LSxxx, 89LPxxx, 89Exxx, 89Lxxx, all manufacturers, Philips LPC series
  • Microcontrollers Intel 196 series: 87C196 KB/KC/KD/KT/KR/…
  • Microcontrollers Atmel ARM. ARM7: AT91SAM7Sxx, AT91SAM7Lxx, AT91SAM7Xxx, AT91SAM7XCxx, AT91SAM7SExx series ARM9: AT91SAM9xxx series ARM Cortex-M3: AT91SAM3Uxxx  
  • Microcontrollers Atmel AVR 8bit/16bit: AT90Sxxxx, AT90pwm, AT90can, AT90usb, ATtiny, ATmega, ATxmega series
  • Microcontrollers Atmel AVR32: AT32UC3xxxx
  • Microcontrollers Chipcon (TI): CC11xx, CC24xx, CC25xx series
  • Microcontrollers Coreriver: Atom 1.0, MiDAS1.0, 1.1, 2.0, 2.1, 2.2, 3.0 series
  • Microcontrollers Cypress: CY7Cxxxxx, CY8Cxxxxx
  • Microcontrollers ELAN: EM78Pxxx
  • Microcontrollers Infineon(Siemens): XC800, C500, XC166, C166 series
  • Microcontrollers MDT 1xxx and 2xxx series
  • Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx, PIC17Cxxx, PIC18xxx, PIC24xxx, dsPIC, PIC32xxx series
  • Microcontrollers Motorola/Freescale: HC05, HC08, HC11, HC12, HCS08, RS08, S12, S12X, MC56F, MCF51, MCF52 series
  • Microcontrollers Myson MTV2xx, 3xx, 4xx, 5xx, CS89xx series
  • Microcontrollers National: COP8xxx series
  • Microcontrollers NEC: uPD70Fxxx, uPD78Fxxx series
  • Microcontrollers Novatek: NT68xxx series
  • Microcontrollers Nuvoton (Winbond): N79xxx, W77xxx, W78xxx, W79xxx, W83xxx series
  • Microcontrollers Philips (NXP) UOC series: UOCIII, UOC-TOP, UOC-Fighter series
  • Microcontrollers Philips (NXP) ARM7: LPC2xxx, PCD807xx, SAF7780xxx series
  • Microcontrollers Scenix (Ubicom): SXxxx series
  • Microcontrollers Renesas: R8C/Tiny series
  • Microcontrollers SGS-Thomson: ST6xx, ST7xx, ST10xx, STR7xx series
  • Microcontrollers SyncMOS: SM59xxx, SM73xxx, SM79xxx, SM89xxx series
  • Microcontrollers & Programmable System Memory STMicroelectronics: uPSD, PSD series
  • Microcontrollers STM: ST6xx, ST7xx, ST10xx, STR7xx, STR9xx, STM32Fxx, STM8A/S/L series
  • Microcontrollers Silicon Laboratories(Cygnal): C8051 series
  • Microcontrollers Texas Instruments: MSP430, MSC12xx series, TMS320F series
  • Microcontrollers Texas Instruments (ex Luminary Micro): LM3Sxxx, LM3Sxxxx series
  • Microcontrollers ZILOG: Z86/Z89xxx and Z8Fxxxx, Z8FMCxxxxx, Z16Fxxxx, ZGP323xxxxxx, ZLF645xxxxxxx, ZLP12840xxxxx, ZLP323xxxxxxx series
  • Microcontrollers other: EM Microelectronic, Fujitsu, Goal Semiconductor, Hitachi, Holtek, Novatek, Macronix, Princeton, Winbond, Samsung, Toshiba, Mitsubishi, Realtek, M-Square, ASP, Coreriver, Gencore, EXODUS Microelectronic, Megawin, Syntek, Topro, TinyARM, VersaChips, SunplusIT, Nordic, M-Square, QIXIN, Signetic, Tekmos, Weltrend, Amic, Cyrod Technologies, Ember, Ramtron, Nordic Semiconductor, Samsung …

W układzie ISP

  • Serial E(E)PROM: IIC series, MW series, SPI series, KEELOQ series, PLD configuration memories, UNI/O series
  • 1-Wire E(E)PROM: DS1xxx, DS2xxx
  • Serial Flash: standard SPI (25xxx), DataFlash (AT45Dxxx, AT26Dxxx)
  • Microcontrollers Atmel: AT89Sxxx, AT90pwm, AT90can, AT90usb, AT90Sxxxx, ATtiny, ATmega, ATxmega, AT89LSxxx, AT89LPxxx
  • Microcontrollers Atmel AVR32: AT32UC3xxxx
  • Microcontrollers Chipcon (TI): CC11xx, CC24xx, CC25xx series
  • Microcontrollers Cypress: CY8C2xxxx
  • Microcontrollers Elan: EM78Pxxx, EM6xxx series
  • Microcontrollers EM Microelectronic: 4 and 8 bit series
  • Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx, PIC17xxx, PIC18xxx, PIC24xxx, dsPIC, PIC32xxx series
  • Microcontrollers Mitsubishi: M16C
  • Microcontrollers Motorola/Freescale: HC08 (both 5-wire, All-wire), HC11, HC12, HCS08, S12, S12X, MC56F, MCF52 series
  • Microcontrollers Nordic Semiconductor: nRF24xxx
  • Microcontrollers NEC: uPD7xxx series
  • Microcontrollers Philips (NXP): LPC1xxx, LPC2xxx, LPCxx series, 89xxx series
  • Microcontrollers Renesas: R8C/Tiny series
  • Microcontrollers Realtek, M-Square
  • Microcontrollers Scenix (Ubicom): SXxxx series
  • Microcontrollers STM: ST7xxx, STR7xx, STR9xx, STM32Fxx, STM8A/S/L series
  • Microcontrollers Silicon Laboratories(Cygnal): C8051 series
  • Microcontrollers & Programmable System Memory STMicroelectronics: uPSD, PSD series
  • Microcontrollers TI: MSP430 (both JTAG and BSL series), MSC12xxx series
  • Microcontrollers ZILOG: Z8Fxxxx, Z8FMCxxxxx, Z16Fxxxx series, ZLF645x0xx
  • Various PLD (also by Jam/VME/SVF/STAPL/… Player/JTAG support):
  • Altera: MAX 3000A, MAX 7000A, MAX 7000B, MAX 7000S, MAX 9000, MAX II/G/Z
  • Xilinx: XC9500, XC9500XL, XC9500XV, CoolRunner XPLA3, CoolRunner-II
  • PLD Lattice: ispGAL22xV10x, ispLSI1xxxEA, ispLSI2xxxE, ispLSI2xxxV, ispLSI2xxxVE, ispLSI2xxxVL, M4-xx/xx, M4LV-xx/xx, M4A3-xx/xx, M4A5-xx/xx, LC4xxxB/C/V/ZC/ZE, ispCLOCK, Power Manager/II, ProcessorPM
  • FPGA: Actel: ProASIC3, IGLOO, Fusion
  • FPGA: Lattice: MachXO, LatticeXP, ispXPGA

Recently Viewed

  • Recently Viewed Products is a function which helps you keep track of your recent viewing history.
    Shop Now